What this unit covers
Major Work Activity B of the 2025 RSOS: installing, servicing and maintaining generating, distribution and service systems. Its tasks carry 28 of the 100 exam questions: consumer/supply services and metering equipment (B-7, 4), protection devices (B-8, 4), power distribution equipment (B-9, 4), power conditioning, UPS and surge suppression (B-10, 2), bonding, grounding and ground fault protection (B-11, 4), power generation and conversion (B-12, 2), renewable energy and storage (B-13, 2), high-voltage systems (B-14, 2) and transformers (B-15, 4). These are original, independent practice notes; they are not documents of the Red Seal Program, the CCDA or any provincial authority. Code questions are answered with your own copy of the Canadian Electrical Code 2024, provided in the exam room; these notes reproduce none of its tables or values.
Services and metering
- 347/600 V system: 600 V is measured line to line; phase-to-neutral voltage = 600 / 1.73 = 347 V. (RSOS sub-task B-7.02).
- Drip loop: lets water fall from the lowest point of the loop before it reaches the service head (RSOS sub-task B-7.01).
- Neutral: grounded at the point of service only; grounding it again downstream creates shock hazards (RSOS sub-task B-7.01).
- Current transformer (CT): the secondary stays closed under load; install the shorting link before removing meter leads, because an open secondary develops a dangerous high voltage (RSOS sub-tasks B-7.04 and B-15.05).
Protection devices
- Interrupting rating: must be at least the available short-circuit current (RSOS sub-task B-8.01).
- LINE and LOAD: supply on LINE, branch conductors on LOAD (RSOS sub-task B-8.01).
- GFCI, AFCI, SPD: a GFCI senses leakage to ground; a combination-type AFCI detects series and parallel arcing; an SPD such as an MOV diverts surge energy to limit voltage and gives no overcurrent protection (RSOS sub-task B-8.02).
Distribution equipment and UPS
- Torque: lug torque comes from the equipment manufacturer's specifications (RSOS sub-task B-9.01).
- Load balance: spread single-phase loads across the phases (RSOS sub-task B-9.01).
- UPS hazards: utility, bypass and battery can all feed the output; check polarity and string voltage before closing the battery breaker (RSOS sub-tasks B-10.01 and B-10.02).
- Apparent power: 1.73 × line voltage × line current (RSOS sub-task B-10.01).
Bonding, grounding and ground faults
- Bonding: keeps non-current-carrying metal continuous so fault current has a low-impedance path and the overcurrent device operates; bonding is not grounding (RSOS sub-task B-11.01).
- NGR: limits ground fault current, which reduces damage (RSOS sub-task B-11.02).
- Ungrounded system: runs with a first fault; locate and clear it, since a second fault becomes phase to phase through ground (RSOS sub-task B-11.02).
- Extra-low voltage dc: 60 V dc since the 2024 CEC; 42.4 V dc is outdated. High voltage dc moved from 1,000 V to 1,500 V (RSOS sub-task B-11.01).
Generation, renewables and high voltage
- Synchronizing: equal voltage, frequency, phase sequence and phase angle before closing; frequency = number of poles × speed / 120 (RSOS sub-task B-12.01).
- PV arrays: open-circuit voltage is highest on cold, clear mornings; DC conductors stay energized whenever light falls on the modules (RSOS sub-tasks B-13.01 and B-13.02).
- Safety grounds: test and establish isolation first, as in section 8.19 of the COHSR, an example of this common principle (RSOS sub-task B-14.03).
Transformers
- Frequency: a transformer never changes it (RSOS sub-task B-15.02).
- Turn ratio: currents are inverse to voltages: Is = Ip × Ep / Es (RSOS sub-task B-15.02).
- Polarity test: with H1 jumpered to the neighbouring low-voltage terminal, a reading above the applied voltage means additive polarity (RSOS sub-task B-15.02).
Sample questions (5)
1. Which voltage is measured between any phase conductor and the neutral of a 347/600 V three-phase four-wire service?
- 120 volts
- 208 volts
- 347 volts
- 600 volts
On a 347/600 V system the 600 V value is measured between two phase conductors, and the phase-to-neutral voltage is 600 divided by 1.73, which gives 347 V (RSOS sub-task B-7.02 covers three-phase services). The 120 V and 208 V values belong to a 120/208 V service, and 600 V is the line-to-line voltage.
2. A meter is connected to a current transformer marked 400:5. What does this ratio mean?
- The secondary carries 5 A when the primary carries 400 A
- The primary has 400 turns and the secondary has 5 turns
- The secondary voltage is 5 V when the primary is 400 V
- The transformer can be loaded to a maximum of 405 A
A turn ratio relates primary and secondary current as Np/Ns = Is/Ip, so with a 400:5 CT, 400 A in the primary produces 5 A in the secondary (RSOS sub-task B-7.01 lists CTs among metering equipment). Reading the marking as 400 primary turns and 5 secondary turns inverts the turns ratio, since a CT primary has fewer turns than its secondary; the voltage statement confuses a CT with a voltage transformer, and the ratio is neither a sum nor a loading limit.
3. A motor circuit draws a high current for a few seconds while starting. Which fuse type tolerates this inrush but still opens on a sustained overload?
- A fast-acting cartridge fuse
- A single-element link fuse
- A non-delay plug-type fuse
- A time-delay cartridge fuse
RSOS sub-task B-8.01 lists fuses among the overcurrent protection devices, and a time-delay fuse has a thermal element that rides through a short inrush while opening on a sustained overload. Fast-acting, single-element and non-delay fuses react quickly to brief surges, so they can open while the motor is starting.
4. The conductors of an overhead single-phase service enter a weatherhead at the top of the service mast. What keeps rain from running along the conductors into the mast?
- A taut, straight run of each conductor into the service head
- A drip loop formed in each conductor below the service head
- Electrical tape wound around each conductor at the service head
- Antioxidant compound brushed along each conductor outside the mast
RSOS sub-task B-7.01 covers overhead services and the service mast. A drip loop lets water fall from the lowest point of the loop before it reaches the service head. A taut run gives water a direct path inward, tape wrapped on the conductors does not seal reliably against rain, and antioxidant compound belongs on terminations, not on weather protection.
5. A 120/240 V single-phase three-wire service feeds a panel. When the loads on the two ungrounded conductors are unequal, what current does the neutral carry?
- The sum of the two ungrounded conductor currents
- The current of the lighter-loaded ungrounded conductor
- The difference of the two ungrounded currents
- No current, because the neutral serves as a bonding path
In the Edison three-wire system (RSOS sub-task B-7.01) the two ungrounded currents oppose each other in the neutral, so the neutral carries their difference. The sum would apply only if the loads were on the same conductor, the lighter current is not what is left over, and a service neutral is a current-carrying conductor, unlike a bonding conductor.